A Compositional Model for CO2 Floods Including CO2 Solubility in Water
- Yih-Bor Chang (Western Atlas Software) | Brian K. Coats (Western Atlas Software) | James S. Nolen (Western Atlas Software)
- Document ID
- Society of Petroleum Engineers
- SPE Reservoir Evaluation & Engineering
- Publication Date
- April 1998
- Document Type
- Journal Paper
- 155 - 160
- 1998. Society of Petroleum Engineers
- 2.7.1 Completion Fluids, 5.4.1 Waterflooding, 5.8.8 Gas-condensate reservoirs, 5.2.1 Phase Behavior and PVT Measurements, 5.5 Reservoir Simulation, 5.2 Reservoir Fluid Dynamics, 5.2.2 Fluid Modeling, Equations of State, 5.4.2 Gas Injection Methods, 5.4 Enhanced Recovery, 2.2.2 Perforating, 5.5.1 Simulator Development
- 15 in the last 30 days
- 2,370 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 10.00|
|SPE Non-Member Price:||USD 30.00|
This paper presents a three-dimensional, three-phase compositional model for simulating CO2 flooding including CO2 solubility in water. Both fully implicit and IMPES formulations are included. In this model, CO2 is allowed to dissolve in the aqueous phase while all other components except water exist in the oil and gas phases. Oil- and gas-phase densities and fugacities are modeled by a cubic equation of state. The aqueous phase properties are functions of the amount of dissolved CO2. CO2 solubility is computed using a CO2 fugacity coefficient table that is converted internally from input CO2 solubility data as a function of pressure at reservoir temperature. Correlations for computing the solubility of CO2 in water and other properties of CO2 saturated water are presented. Results for simulation runs with and without CO2 solubility in water are shown for comparison. IntroductIon Compositional models using a cubic equation of state are usually used to simulate the enhanced recovery process of gas injection. In most of the published models, for example Coats and Young and Stephenson, all hydrocarbon components exist in the oil and gas phases but are not allowed to dissolve in the aqueous phase. Usually, this assumption is adequate since the hydrocarbon solubility in water is low over the range of temperature and pressure for gas injection. Carbon dioxide, however, is an exception to this assumption. The solubility of CO2 in water is much higher than that of hydrocarbon components and is a factor that can not be neglected in the simulation process. This is especially true when CO2 is injected into a previously waterflooded reservoir or when CO2 is injected with water for mobility control. Tile objective of this paper is to model oil recovery processes involving CO2 injection while taking into account the effects of CO2 solubility in water.
The effects of the presence of an aqueous phase on the phase behavior of CO2/hydrocarbon systems have been experimentally studied by Pollack et al. It was found that the presence of water reduces the amount of CO2 available for mixing with the hydrocarbons, and shifts the pressure-composition diagram of CO2/crude oil system. The solubility of CO2 in water is a function of temperature, pressure and water salinity. A thorough study of CO2 solubility data in distilled water was presented by Dodds et al. In general, CO2 solubility increases with pressure and decreases with temperature. An increase in salinity of the reservoir water decreases CO2 solubility significantly. Li and Nghiem used Henry's Law to estimate CO2 solubility in distilled water and used the scaled-particle theory to take into account the presence of salt in the aqueous phase. Enick and Klara also used Henry's Law to predict CO2 solubility in distilled water. Tile decreased solubility of CO2 in brine was accounted for empirically by a single factor correlated to the weight percent of dissolved solid. However, a wide scatter of data characterizes their correlation.
A compositional model for simulating CO2 floods including CO2 solubility in water is presented. In this model, hydrocarbons and CO2 are allowed to exist in the oil and gas phases while only CO2 and water exist in the aqueous phase. A cubic equation of state is used to model oil- and gas-phase densities and fugacities. An input table of CO2 solubility in water, water formation volume factor, water compressibility and water viscosity is required for this model. These data, which are obtained either experimentally or generated from correlations, are entered as a function of pressure at reservoir temperature. The CO2 solubility in water is internally converted into a fugacity coefficient table as a function of pressure. The fugacity coefficients are then used to compute the amount of CO2 in water during simulation using the equality of component chemical potential constraint. The water formation volume factor, compressibility and viscosity are then computed as a function of the amount of CO2 dissolved in the water.
|File Size||179 KB||Number of Pages||6|