Predicting and Applying Wellhead Temperatures for Steamflood-Field Operation and Production-Performance Monitoring
- Zhengming Yang (Aera Energy LLC)
- Document ID
- Society of Petroleum Engineers
- SPE Reservoir Evaluation & Engineering
- Publication Date
- August 2020
- Document Type
- Journal Paper
- 1,031 - 1,044
- 2020.Society of Petroleum Engineers
- surface facility design, production performance monitoring and optimization, steamflood wellhead temperature prediction
- 4 in the last 30 days
- 66 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 5.00|
|SPE Non-Member Price:||USD 35.00|
Producer-flowline temperatures (FLTs) can be measured automatically with a thermistor on an emergency-shutdown system (ESD), or manually on a specified spot on flowline with a handheld unit. Measured FLTs can usually be mapped to represent the formationtemperature distribution for steamflood reservoir management purposes (Hong 1994; Nath et al. 2007). In addition to FLT, wellhead temperature (WHT) is another surface temperature. Predicting the long-term WHT trend in steamflood operation is necessary for designing surface facilities for both oil dehydration/separation and produced-water recycling. This predicted temperature will also be applicable for production-performance monitoring.
To predict the wellhead temperature, Hasan et al. (2009) derived a steady-state analytical solution for calculating WHT from bottomhole temperature (BHT) under flowing conditions of a multisection slant wellbore for the isothermal primary-depletion process, with both WHT and BHT being time independent for a given gross rate (Igec et al. 2010). This steady-state analytical solution has been extended to calculate steamflood producer WHT from BHT (both are time dependent) by consecutively approximating the WHT and monthly average of FLT measurements to a steady-state solution. The monthly averaged FLTs are seasonally variable and higher in the summer months of July through September and lower in the winter months of December through February. Monthly averaged FLT measurements depend on an annual ambient-temperature cycle within the depth needed for reaching an undisturbed ground temperature (typically 30 to 50 ft) (Gwadera et al. 2017). WHT, if measured, should be comparable with FLT for their close typical distance of 5 to 10 ft. WHT prediction, however, is only process dependent and not seasonally variable because of the inability to describe seasonally undisturbed depth in the geothermal gradient. Therefore, WHT prediction can be validated with average summer-month FLT measurements when heat loss becomes minimal. BHTs in this analytical approach are predicted by the Lauwerier (1955) analytical model and improved by calibration with the available reservoir-simulation model or several years of FLT measurements for steamflood response time.
The objective of this study is to develop an integrated production-monitoring approach using only the surface information, including WHT and FLT, oil/water-production rate, and injection-pressure/rate data, which can be applied to diagnose and optimize steamflood production performance. A field case study for the South Belridge Diatomite steamflood was investigated. WHT prediction is compared with FLT measurement for diagnosing and understanding the production performances, such as premature water or steam breakthrough, interference by the waterflood on the steamflood boundary producers, as well as the FLT variation related to the target rates for steam injection. This diagnostic analysis approach combined with the Buckley-Leverett theory-based displacement-efficiency analysis, and injection pressure and rate signal, will help to develop an improved understanding of the displacement detail and form a decision base to optimize the production performance.
|File Size||5 MB||Number of Pages||14|
Dietrich, J. 1990. Steamflooding in a Waterdrive Reservoir: Upper Tulare Sands, South Belridge Field. SPE Res Eval & Eng 5 (3): 275–284. SPE-17453-PA. https://doi.org/10.2118/17453-PA.
Gwadera, M., Larwa, B., and Kupiec, K. 2017. Undisturbed Ground Temperature—Different Methods of Determination. Sustainability 9 (11): 1–14. https://doi.org/10.3390/su9112055.
Hasan, A. R., Kabir, C. S., and Wang, X. 2009. A Robust Steady-State Model for Flowing Fluid Temperature in Complex Wells. SPE Prod & Oper 24 (2): 269–276. SPE-109765-PA. https://doi.org/10.2118/109765-PA.
Hong, K. C. 1994. Steamflood Reservoir Management: Thermal Enhanced Oil Recovery. Tulsa, Oklahoma, USA: PennWell Books.
Izgec, B., Hasan, A. R., Lin, D. et al. 2010. Flow-Rate Estimation from Wellhead-Pressure and Temperature Data. SPE Prod & Oper 25 (1): 31–39. SPE-115790-PA. https://doi.org/10.2118/115790-PA.
Lauwerier, H. A. 1955. The Transport of Heat in an Oil Layer Caused by the Injection of Hot Fluid. Appl. Sci. Res. A 5: 145–150. https://doi.org/10.1007/BF03184614.
Marx, J. W. and Langenheim, R. H. 1959. Reservoir Heating by Hot Fluid Injection. SPE-1266-G.
Nath, D. K., Sugianto, R., and Finley, D. B. 2007. Fiber-Optic Distributed Temperature Sensing Technology Used for Reservoir Monitoring in an Indonesia Steam Flood. SPE Drill & Compl 22 (2): 149–156. SPE-97912-PA. https://doi.org/10.2118/97912-PA.
Neuman, C. H. 1985. A Gravity Override Model of the Steamdrive. J Pet Technol 37 (1): 163–169. SPE-13348-PA. https://doi.org/10.2118/13348-PA.
Qi, Q., Pepin, S., Al Jazzaf, A. et al. 2017. Errors Associated with Waterflood Monitoring Using the Hall Plot for Stacked Reservoirs in the Absence of Profile Surveys. Paper presented at the SPE Western Regional Meeting, Bakersfield, California, USA, 23–27 April. SPE-185694-MS. https://doi.org/10.2118/185694-MS.
Ramey, H. J. Jr. 1962. Wellbore Heat Transmission. J Pet Technol 14 (4): 427–435. SPE-96-PA. https://doi.org/10.2118/96-PA.
Saeid, S. and Barends, F. B. J. 2009. An Extension of Lauwerier’s Solution for Heat Flow in Saturated Porous Media. Oral presentation given at the COMSOL Conference, Milan, Italy, 14–16 October.
Silin, D. B., Holtzman, R., Patzek, T. W. et al. 2005. Waterflood Surveillance and Control: Incorporation Hall Plot and Slope Analysis. Paper presented at the SPE Annual Technical Conference and Exhibition, Dallas, Texas, USA, 9–12 October. SPE-95685-MS. https://doi.org/10.2118/95685-MS.
Yang, Z. 2009. A New Diagnostic Analysis Method for Water Performance. SPE Res Eval & Eng 12 (2): 341–351. SPE-113856-PA. https://doi.org/10.2118/113856-PA.
Yang, Z. M. 2012. Production-Performance Diagnostics Using Field-Production Data and Analytical Models: Method and Case Study for the Hydraulically Fractured South Belridge Diatomite. SPE Res Eval & Eng 15 (6): 712–724. SPE-153138-PA. https://doi.org/10.2118/153138-PA.
Yang, Z. M. and Urdaneta, A. 2017. A Practical Approach to History Matching Premature Water Breakthrough in Waterflood Reservoir Simulation: Method and Case Studies in South Belridge Diatomite Waterflood. SPE Res Eval & Eng 20 (3): 726–737. SPE-174006-PA. https://doi.org/10.2118/174006-PA.