A New and Practical Workflow for Large Multipad SAGD Simulation—An Oil-Sands Case Study
- Colin C.H. Card (Computer Modelling Group Limited) | Anjani Kumar (Computer Modelling Group Limited) | Jason C. Close (Computer Modelling Group Limitedd.) | Arnfinn Kjosavik (Statoil ASA (Norway)) | Hafsteinn Agustsson (Statoil ASA (Norway)) | Matteo M. Picone (Statoil Canada Limited)
- Document ID
- Society of Petroleum Engineers
- Journal of Canadian Petroleum Technology
- Publication Date
- January 2014
- Document Type
- Journal Paper
- 14 - 31
- 2014.Society of Petroleum Engineers
- 4.3.4 Scale, 5.8.5 Oil Sand, Oil Shale, Bitumen, 5.3.9 Steam Assisted Gravity Drainage, 5.5 Reservoir Simulation, 4.1.2 Separation and Treating
- numerical tuning
- 1 in the last 30 days
- 577 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 12.00|
|SPE Non-Member Price:||USD 35.00|
Every simulation engineer wishes to simulate large full-field models, but historically reservoir simulation of the steam-assisted-gravity- drainage (SAGD) process has been constrained to single-well models up to a single pad. Models of these sizes provide valuable information and have helped to assess the development potential of reservoirs. These models may be used for reservoir management and to support the decision-making process for the design of the initial completion, operating strategy, and multipad wind-down evaluations, and also qualitatively assess the uncertainty in the SAGD forecast under different geological settings. However, in many cases we are left with the question of how multiwell and multipad communications ultimately affect performance at the well-pair scale. Because of technological constraints with computer hardware and simulation technology, running extremely large multipad models has been until recently largely impractical, especially when trying to run multiple scenarios to better understand the impact of geological and operational uncertainty. In this paper, we present a new and practical workflow that makes running extremely large multipad, multimillion-grid-cell SAGD models a reality. The three major steps of the workflow are (1) generating simulation-friendly geomodels, (2) use of experimental design and 3D submodels on the basis of SAGD performance index (SPI) for numerical tuning, and (3) use of 2D cross sections and SPI to develop dynamic grid-refinement-parameter values for the full 3D model. All of these steps are intended to improve the numerical stability and run time of multipad SAGD simulation models. A 24-SAGD-well-pair model with 2.52 million gridblocks was simulated for 10 years of forecast. The reservoir is geologically complex and highly heterogeneous. We discuss some of the important aspects that need to be accounted for when simulating large-scale SAGD models. Using this new workflow, the simulation run time was reduced from 42 days to 7 days on eight central processing units (CPUs)—a six-time speedup. The resulting run time is short enough to facilitate multirealization simultaneous runs using eight CPUs, hence maximizing the throughput and minimizing the simulation cycle time. This new workflow can be easily replicated and, more importantly, automated to reduce engineering time requirements. While this paper focuses on the SAGD process, this methodology is completely generic in that it can be applied to any large data set for any process. Details will differ depending on the process, but the workflow will be the same.
|File Size||2 MB||Number of Pages||18|
Fenik, D.R. 2010. Practical Use of Multiple Geostatistical Realizations in Petroleum Engineering. MS thesis, Department of Civil & Environmental Engineering, University of Alberta, Calgary, Alberta.
Kennedy, J. and Eberhardt, R.C. 1995. Particle swarm optimization. Proc., 1995 IEEE International Conference on Neural Networks, Perth, Western Australia, 27 November–1 December, 1942–1947.
McLennan, J. and Deutsch, C.V. 2005. Ranking Geostatistical Realizations By Measures of Connectivity. Presented at the SPE/PS-CIM/CHOA International Thermal Operations and Heavy Oil Symposium, Calgary, 1-3 November. SPE-98168-MS. http://dx.doi.org/10.2118/98168-MS.