Impact of Slow and Fast Warm-Up Rates on Cement Sheath Integrity in SAGD Wells: Using Dynamic Flow Simulators for Early Time Analysis
- C. M. Nascimento (Schlumberger) | B. Demirdal (Devon Energy)
- Document ID
- Society of Petroleum Engineers
- SPE Thermal Well Integrity and Design Symposium, 28-30 November, Banff, Alberta, Canada
- Publication Date
- Document Type
- Conference Paper
- 2017. Society of Petroleum Engineers
- 5.6.11 Reservoir monitoring with permanent sensors, 5.3.9 Steam Assisted Gravity Drainage, 1.14 Casing and Cementing, 1.6 Drilling Operations, 2 Well completion, 3 Production and Well Operations, 5.4.6 Thermal Methods, 2.10 Well Integrity, 2.10.3 Zonal Isolation
- Earl stage, Dynamic Flow Simulations, SAGD, Heat Transfer, Cement Integrity
- 3 in the last 30 days
- 105 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 8.50|
|SPE Non-Member Price:||USD 25.00|
The original viscosity of the oil in place is greater than 1,000,000 centipoises in most cases in Western Canada. As a result, steam assisted gravity drainage (SAGD) is a widely used thermal recovery method to produce bitumen reserves for the last 10-15 years. SAGD involves drilling two horizontal wells (one on top of each other roughly 5 meters) apart and injecting steam from the top well (called "injector") to reduce the viscosity of oil in place by heating and produce the flowing oil from the bottom one (called "producer").
Initially, there is very little to no pressure communication between the injector and producer since the bitumen is in solid state. As a result, in order to initiate communication between the wells so steam injection can penetrate into the reservoir to heat the rock and the fluids, both wells were circulated with steam and this phase is called "circulation". During circulation, steam is injected to the wells through long tubing and returns are received back through short tubing. In addition to be quite critical to the overall production performance of the reservoir, circulation phase has a critical impact on the integrity of the well since during this phase the well was introduced to heating for the first time. Considering the fact that steam is being injected in a cold well, thermal loading impacts on casing and cement are expected to be the highest during earlier times of circulation. While injecting steam at higher rates as early as possible has operational benefits, effects of such practice on zonal isolation should be evaluated in detail.
A well operated by Devon in Jackfish field was used for this purpose and a dynamic flow simulator was modelled to investigate the impact of slow (going from 1 ton/hr to 5 ton/hr in 5 days) versus fast warm-up during early stages of circulation phase on cement sheath. Field data captured by distributed temperature sensing system (DTS) was used to validate the model and comparison on cement heating rate at different depth intervals during slow and fast warm up cases were made to determine at what depths and durations the heating rates of cement are different between the two cases.
The combination of the field results and simulation enabled to determine the critical time frame where different circulation strategies have the highest impact on cement heating rates. The simulation results also provided insight on transient temperature distribution across wellbore and near wellbore during early times of circulation.
|File Size||5 MB||Number of Pages||20|
Bendiksen, K. H., Malnes, D., Moe, R. et al. 1991. The Dynamic Two-Fluid Model OLGA: Theory and Application. SPE Prod Eng 6 (2): 171–180. SPE-19451-PA. http://dx.doi.org/10.2118/19451-PA.
Medina, M. and Wat, R. 2012. Integrating Wellbore Hydraulics, Reservoir Properties, and Thermal Transient Analysis for SAGD Injector Well Completion Design with Multiple Outflow Control Devices: A Case Study. Presented at the SPE Western Regional Meeting, Bakersfield, California, USA, 19-23 March. SPE-153909-MS. http://dx.doi.org/10.2118/153909-MS.
Nascimento, C. M. 2016. Design, Optimization and Operation of SAGD Wells Using Dynamic Flow Simulations. Presented at the SPE Western Regional Meeting, Anchorage, Alaska, USA, 23-26 May. SPE-180459-MS. http://dx.doi.org/10.2118/180459-MS.