Mechanical Evaluation of a New Premium Screen - FacsRiteTM - for SAGD Applications
- Glenn E. Woiceshyn (Absolute Completion Technologies) | Ezio P. Toffanin (Schlumberger) | Jueren Xie (C-FER Technologies) | Brian Wagg (C-FER Technologies) | Chengye Fan (C-FER Technologies)
- Document ID
- Society of Petroleum Engineers
- International Thermal Operations and Heavy Oil Symposium, 20-23 October, Calgary, Alberta, Canada
- Publication Date
- Document Type
- Conference Paper
- 2008. SPE/PS/CHOA International Thermal Operations and Heavy Oil Symposium
- 4.3.4 Scale, 4.2.3 Materials and Corrosion, 1.8 Formation Damage, 2.4.4 Screen Selection, 2.4.6 Frac and Pack, 5.4.6 Thermal Methods, 5.8.5 Oil Sand, Oil Shale, Bitumen, 5.3.9 Steam Assisted Gravity Drainage, 4.1.5 Processing Equipment, 5.1 Reservoir Characterisation, 2.4.3 Sand/Solids Control, 6.5.2 Water use, produced water discharge and disposal, 1.6 Drilling Operations, 1.14.1 Casing Design, 4.1.2 Separation and Treating
- 0 in the last 30 days
- 687 since 2007
- Show more detail
- View rights & permissions
|SPE Member Price:||USD 9.50|
|SPE Non-Member Price:||USD 28.00|
Steam assisted gravity drainage (SAGD) wells typically require the deployment of an open hole completion combining sand control with adequate mechanical strength to withstand: 1) aggressive installation loads—compression, torque, bending—that are characteristic of shallow horizontal wells, and 2) severe operational loads—tension, compression, collapse, burst—caused by a combination of high temperature steam injection and formation collapse around the completion.
Historically, slotted liners have been used in Western Canada, primarily because of low cost relative to wire-wrapped screen (WWS) or premium mesh screens. However, slotting base pipe can significantly weaken its mechanical strength, particularly in torsion and collapse, and the slot width can change as the liner deforms under certain load conditions. Reported incidents of mechanical failure and loss of sand control of slotted liners in SAGD wells have generated interest among operators to investigate alternative technologies.
A new sand screen has been developed that involves flush-mounting and securing 25.4 mm diameter fusion bonded metal laminate (FBML) cartridges/discs directly into the base pipe wall. The open flow area of the screen, which can be as high as 20% (versus 2.5% for slotted liner), is dictated by the number of inserted discs (holes) per foot. For an equivalent open flow area, drilling holes in the base pipe is less detrimental to the mechanical strength of the liner than cutting slots. This new geometry results in a sand screen that is cost competitive to slotted liner on a same-open-flow-area basis, significantly stronger, and comparable to a premium mesh screen in terms of sand retention performance.
To independently quantify the mechanical strength and integrity of this new screen for SAGD, an extensive Finite Element Analysis study was performed on 177.8 mm (7??), 38.7 kg/m (26 lb/ft), L80 base pipe for two different hole densities and various single loads, combined loads and thermal cycling. The results, as presented herein, demonstrate that inserting FBML discs into base pipes does not significantly weaken it compared to cutting slots. A stand alone screen (SAS) with almost four times the open flow area of a slotted liner has significantly more torsion and collapse strengths.
SAGD wells are horizontal and typically completed in shallow, unconsolidated heavy oil reservoirs with a liner or Stand Alone Screen (SAS) for sand control. A typical SAGD completion requires adequate mechanical strength to withstand 1) aggressive installation loads—compression, torque, bending—that are characteristic of shallow horizontal wells, and 2) severe operational loads—tension, compression, collapse—caused by high temperature steam injection in combination with formation collapse around the screen. Any deformation of the liner/screen due to such loads must not impair sand control or the production/injection of oil/steam.
|File Size||1 MB||Number of Pages||15|